eDAQ


Specification
Physical
  • Size: 23cmW x 27.6cmL x XcmH
  • Weight: X kg
  • Operating Temperature: -20° to 65° C
  • NOTE: X is a variable that is dependent on the configuration of the system.

Enclosure
  • Sealed System: Machined Aluminum case and sealed gaskets protect the system from humidity, corrosion, water spray, and dust.
  • Vibration Tested: Swept sine tested from 5 to 2000 Hz @ 20 G’s
  • Modular: Layers can be custom configured pending testing requirements

System
  • Input Power: 10–60 VDC
  • Internal Back-up Battery
  • Sample Rates: Master Clock Rates 100 kHz = 0.1Hz to 100 kHz98.3 kHz = 0.1 Hz to 98,304Hz
  • Communications : Ethernet 100 BaseT Serial RS232 up to 115,200 baud
  • Memory : Internal Flash 4GB, 8GB, 16GB, 32GB

ECOM
Overview
The Vehicle Network Communications Layer (ECOM) offers
(3) CAN device interfaces, (1) Vehicle Bus Module (VBM)
interface and a GPS communications port.

Specifications
Five communications channels; (3) CAN, (1) Vehicle Bus

Module (VBM) and (1) GPS.
• Size: 23 cm W x 25 cm L x 3.3 cm H
• Weight: 2.0 kg
• Inputs: (3) High Speed CAN

(1) Vehicle Bus Module (VBM)
(1) GPS Communications

EHLS
Overview
The Simultaneous High Level Board (EHLS) offers 16
simultaneously sampled high-level differential analog inputs
through independent connectors.

Specifications
• Size: 23 cm W x 25 cm L x 3.3 cm H
• Weight: 2.0 kg
• Inputs: Minimum full–scale range ±62.5mV
    Maximum full–scale range is ±80V
• Resolution: 16-bit ADC, across specified full-scale range
• Sample Rates: Independently set from 0.1Hz to 100kHz
• Transducer Power: 3V to 28V in 1V increments, 500mW per channel
• Analog Out Option (EHLS-AO): +/- 10V output

EBRG
Overview
The Bridge Board, or EBRG, offers 16 low level, simultaneously sampled differential input channels through independent 6- pin Turck connectors.

Specifications
• Size: 23 cm W x 25 cm L x 3.3 cm H
• Weight: 2.0 kg
• Excitation: 5V (Bipolar ±2.5) or 10V (Bipolar ±5)
• Inputs: Minimum full–scale range ±625μV
    Maximum full–scale range is ±10V
• Sample Rates: Independently set from 0.1Hz to 100kHz
• Resolution: 16–bit ADC
• Support 1/4, 1/2, full bridge
• Four shunt calibration resistors per channel
• Analog Out Option (EBRG-XXX-AO): +/- 10V output
EITC
Overview
Each Isolated Thermocouple layer offers eight channels of isolated thermocouple signal conditioning.

Specifications
• Size: 23 cm W x 25 cm L x 3.3 cm H
• Weight: 2.0 kg
• Channels: Eight channels of isolated thermocouple signal conditioning. All must be of the same type.

• Type Range
 -K Type -200 deg.C to 1372 deg.C
 -T Type -200 deg.C to 400 deg.C
 -E Type -200 deg.C to 1000 deg.C
 -J Type -200 deg.C to 1200 deg.C

• Connection: Standard miniature thermocouple connectors
• Isolation: Independently isolated to 500V
• Sample Rates: 0.1Hz to 5Hz maximum
• Accuracy: ±0.5oC typical
EDIO
Overview
The EDIO is an extremely versatile board that can measure digital inputs/outputs, pulse counters, quadrature decoders, vehicle bus, as well as GPS.

Specifications
• Size: 23 cm W x 25 cm L x 3.3 cm H
• Weight: 1.7 kg
• 24 channels of selectable digital input/output, voltage ranges: –0.2 to +45Vdc
• 12 channels of wide range digital input only, voltage ranges: -45 to +45Vdc
• 18 pulse counters with software selectable modes: Pulse Width Period, Pulse On Period, Pulse Rate, and Quadrature Decoder
• Output power: selectable of 5V or 12V at 1A
• GPS Option
• Vehicle Bus Interface – Up to 2 Vehicle Modules per layer
Relationship Files

전체선택 전체해지 선택 다운로드